Setronik 1 Restyling

General Features:

  • Compliance with the standards EN 81-XX;
  • Control of the electric traction with 1/2 speed, with inverter 3VF in open / close loop;
  • Control of the hydraulic traction with direct starting, star/delta starting, Soft Starter starting, with the most common electronic valves;
  • Control of the calls in APB, down collective selective, up/down collective selective;
  • Control of multiplex (Duplex, Triplex and so on);
  • Control of manual doors, semiautomatic doors, automatic doors up to 3 operators with different drivers
  • Control of Fireman operations and Fire-fighting operations (EN81.72, EN81.73)
  • Control of the communication between the controller and the other electronic devices:
    -parallel with the car and the floors;
    -CAN with the car and parallel with the floors;
    -CAN with the car and the floors
  • Diagnostics and Programming of the parameters:
    -with LEDs on the main board displaying the in / out status;
    -with the usual terminal STK2-PM used with the previous controllers Setronik1 and Setronik2;
  • Control of the different parameter configurations and firmware updates with the USB key;
  • Control of the safety chain between 24Vdc to 230Vac;
  • Control of the signallings at 24Vdc 2W

Special features:

  • The main board STK1R (Setronik1 Restyling) can replace the previous main board STK1b (Setronik1) without any electric or mechanical changes;
  • The usual terminal STK2-PM for diagnostics and programming with the previous Setronik1 and Setronik2 works also with the new Setronik1 Restyling;
  • Pre-wiring with connectors without other wiring operations during the installation;
  • Control of the position and speed through:
    -Magnetic contact sensors on the car roof;
    -Encoder on the car roof (supplied by Sea Systems);
    -Encoder on the motor in electric lifts

The STK1R-MR is a type of Control Cabinet with STK1R (Setronik1 Restyling) board, which is specifically designed both for electric and hydraulic lifts with machine room (MR-lifts).

The controller is placed in the machine room.

Controller in the machine room for electric lifts
cod. STK1R-MR-E
Standard control panels for electric lifts direct starting, inverter; interface with different...view
Controller in the machine room for hydraulic lifts
cod. STK1R-MR-H
Standard control panels for hydraulic lifts direct starting, star/delta starting, soft starter...view

The STK1R-MRLP is a type of control cabinet with STK1R (Setronik1 Restyling) board, which is specifically designed both for electric and hydraulic lifts without machine room (MRL-lifts).

The controller is made up of a single component placed on the landing.

Controller at landing for electric lifts
cod. STK1R-MRLP-E
Control cabinets for MRL-electric lifts In column cabinet in stainless steel or plalam; For...view

The STK1R-MRLV is a type of control cabinet with STK1R (Setronik1 Restyling) board, which is specifically designed both for electric and hydraulic lifts without machine room (MRL-lifts).

The controller is split in two parts:
- The main cabinet in the shaft;
- The inspection cabinet in the landing door post

Controller in the shaft for hydraulic lifts
cod. STK1R-MRLV-H
Control panels for MRL-hydraulic lifts. installation of the main controller in the shaft and...view
Controller in the shaft for electric lifts
cod. STK1R-MRLV-E
Control panels for MRL-electric lifts installation of the main controller in the shaft and...view

The STK1R-HL is a type of control cabinet with STK1R (Setronik1 Restyling) board, which is specifically designed for platforms. It can be supplied together with pre-wired systems and push-button panels.

Control panel for hydraulic platforms
cod. STK1R-HL-H
General features: For platforms with hydraulic traction with 1 or 2 speed; Monophasic/three...view